Setting of counting direction of winding machine controller

heading_title

Setting of counting direction of winding machine controller:

         The REPOSAL's  winding machine controller has complete functions and a wide range of applications.Some customers have purchased our winding machine controller.As soon as we delivered the counting sensor, users sometimes find that when they are installed in the winding machine, the counting It will start counting from 9999.9 and become smaller and smaller. This is just because when you don't pay attention, install the counter in the opposite direction.At this time, we don't actually need to disassemble the installed machine. We have taken this into consideration. You need to change the counting direction on the controller.The video below shows that if you use our winding machine controller to change the counting direction.

          

          

Related Post

Winding machine installation: sp-d102-b-6

Winding machine installation: sp-d102-b-6

Install sp-d102-b-6:

   Economical winding machines are divided into different specifications according to the size of the power, according to the different winding machine motors, divided into DC brushless motors and AC variable frequency motors, but according to the different applications, they are divided into the following types:

   The first type is a transformer winding machine, which is characterized by being able to wind several different enameled wires at the same time, but there is no better tension controller, and its tension control is only controlled by the degree of compression of the wool felt.

           The second type is the general coil winding machine, which is mainly used for the general coil of a single enameled wire. The standard tension controller is used. Its standard tensioner has a larger range. In the occasions where the tension requirement is not high, as far as the tensioner is concerned, it The diameter of the enameled wire can range from 0.2-1.4mm.

        The third type is a magnetic damping wire frame winding machine, which is also suitable for the general coil of a single enameled wire, but its tensioner uses a magnetic damping tensioner, from 0.03mm diameter enameled wire to 0.5mm diameter enameled wire, which is divided into There are many specifications. The advantage is that it has relatively stable tension and can be used to wind thin enameled wires. The disadvantage is that enameled wires with a diameter of 0.03mm-0.5mm require a variety of tensioners.

   The fourth type is the motor coil winding machine, which is mainly used for winding the motor coil. The torque of the winding machine is large. The tensioner uses a standard mechanical tensioner, but it is equipped with a wire die.

   The following video shows the installation of a general coil winding machine.

 Electromagnetic coil precision winding machine for winding machine

Electromagnetic coil precision winding machine for winding machine

         Winding machine, when people talk about it, usually refers to a machine that uses enameled wire as a material to form a coil. In the impression, this should be a very simple machine or even some people's printing should be summarized as a simple Power tools. But in fact, this is an industry with a very wide variety, a wide range of coverage, and complex technical characteristics.

        From the processed products, such as the single-axis CNC winding machine for processing high-frequency transformer coils, the winding axis rotates, and the winding axis moves accordingly according to the set pitch. This is a relatively simple winding machine. For example, ordinary relays are characterized by the small diameter of the enameled wire and the relatively large number of turns, so the rotation time of the main shaft of the winding machine is long.The ordinary electromagnetic coil does not have too high requirements for the accuracy of the wiring, so the main requirement for the machine is the speed High and stable tension.

        Then there is the precision electromagnetic coil, which is also an electromagnetic coil, but because this coil has temperature resistance requirements, response speed requirements, wire package volume requirements, and product consistency requirements, it is required that the winding machine be wound during winding. Each wire is neatly arranged, so to achieve this accuracy, there are strict requirements for all process factors in the winding process.

        There is the rotation accuracy of the winding spindle of the winding machine. The control accuracy of the winding machine controller, the repeating positioning accuracy of the wire screw, the roundness of the enameled wire, the diameter of the enameled wire, the rotation of the tooling behind the main shaft of the winding machine Accuracy, tension control of the enameled wire, parallelism of the two ends of the cable cavity during winding, dimensional accuracy, and also includes the structural design of the cavity during cable routing, and the design of stripping after winding. It is directly related to the success of the winding accuracy.
Continuous-execution-of-multiple-programs-of-the-winding-machine

Continuous-execution-of-multiple-programs-of-the-winding-machine

The company's CNC winding machine allows storage of 1000 sets of process data, and supports continuous execution of multiple sets of process data. The number of consecutive execution groups can be set from 2 to 1000 groups. This function is more complicated for the process and requires multiple external The intervention product provides great convenience and flexibility. The following winding machine operation video introduces the specific setting method.

Below we explain the two procedures of the Xiepu winding machine,

        Or continuous automatic execution between multiple programs,

        In other words, after bypassing the first program,

        Then the second program is executed automatically,

        No need for you to press the start button in the middle,

        Let's demonstrate,

        How the settings are set,

        First "step sequence setting" "input"

        In the second program,

        We put "autostart"

        Is now open,

        Then the "autostart" of the first program we have to close it,

        Because if this is the "autostart" of the first program,

        It will become an infinite loop,

        Turn it off now,

        Then press "Enter" and press "Reset"

        All right,

        Then we pay attention to the "" light in the lower left corner to turn on,

        Then we press start.

Setting of counting direction of winding machine controller

Setting of counting direction of winding machine controller

Setting of counting direction of winding machine controller:

         The REPOSAL's  winding machine controller has complete functions and a wide range of applications.Some customers have purchased our winding machine controller.As soon as we delivered the counting sensor, users sometimes find that when they are installed in the winding machine, the counting It will start counting from 9999.9 and become smaller and smaller. This is just because when you don't pay attention, install the counter in the opposite direction.At this time, we don't actually need to disassemble the installed machine. We have taken this into consideration. You need to change the counting direction on the controller.The video below shows that if you use our winding machine controller to change the counting direction.

Setting of counting direction of winding machine controller

Setting of counting direction of winding machine controller

Setting of counting direction of winding machine controller:

         The REPOSAL's  winding machine controller has complete functions and a wide range of applications.Some customers have purchased our winding machine controller.As soon as we delivered the counting sensor, users sometimes find that when they are installed in the winding machine, the counting It will start counting from 9999.9 and become smaller and smaller. This is just because when you don't pay attention, install the counter in the opposite direction.At this time, we don't actually need to disassemble the installed machine. We have taken this into consideration. You need to change the counting direction on the controller.The video below shows that if you use our winding machine controller to change the counting direction.

Setting-of-technological-parameters-of-winding-machine

Setting-of-technological-parameters-of-winding-machine

           The company's CNC winding machine controller has been continuously improved, with complete functions and stable performance. It can accurately set the main parameters such as starting point, wire diameter, width, high speed, low speed, etc., and also include such as start slow speed, stop Auxiliary parameters such as slow speed, stop at both ends, these commonly used parameters are designed in the user parameter setting area. The following video explains the parameter setting process of our company's CNC winding machine in more detail:

          Now we introduce the setting of process parameters of Xiepu winding machine.

          The controller of Xiepu winding machine is divided into these major functions.

          This part is called the digital parameter area.

          It represents the current state of the machine.

          For example, the red light here corresponds to the standby state.

          It means that this machine is in standby state.

          The following states are running, slowing, positioning, speeding.

          This is a status area to monitor the current status of the machine.

          This is a numeric parameter area.

          The digital parameters need to be some numbers that we need to set.

          at this place.

          This is a switch parameter.

          For example, when the cable direction starts.

          Whether from left to right or right to left.

          This is the cable direction.

          There is also the winding direction.

          For example, when we are standing on the right side of the machine.

          See if the spool is rotating clockwise or counterclockwise.

          Then choose the direction.

          Then there are some special functions.

          For example, parking at both ends, automatic stopping, automatic homing, etc.

          These functions may need to be turned on.

          This is a parameter of the nature of the switch.

          So this is a switch parameter area.

          This part is an editing area.

          It is our numbers and clear, copy, confirm, etc.

          This is in the editing area.

          Then this is an interrupt area outside the interrupt area.

          For example, we need to specify the automatic mode.

          Or retreat, jump, stop, start.