Toroidal coil winding machine operation video-Machine operation

heading_title

Toroidal coil winding machine operation video

Below we introduce the structure of this toroidal coil winding machine. This part is the controller and this part is the clamping base. We control the clamping of the product by opening and closing the handle. This position is the storage ring. The enameled wire is stored on the storage ring first, and then wound around this product. This position is a manual winding handle. Turn this handle. The steel plate can be driven manually. The steel ring has an opening. This position is an opening. The opening is opened and closed by sliding the handle up and sliding to the left to open or close. . This position is called the crimping plate, and this position is called the baffle. After the line is removed, its degree of tightness is determined by the tension of the belt. The tension of the belt is adjusted by the tension adjustment knob. When adjusting the belt tension, first loosen And then rotate the handle. When rotating the handle, there is an idler wheel. When the idler wheel goes in, the tension of the belt will increase, so that the winding of the enameled wire will become tighter.

          Let's take a look at how the enameled wire of this toroidal coil winding machine is installed. Put the spool vertically on the ground. This is wool felt. After the copper wheel, then the wool felt, and then the copper wheel in front, note that the degree of clamping of the wool felt can be adjusted by the horn nut, we will now do a demonstration by winding a product, this magnetic ring is picked up , And then the position of the steel ring opening is now here. The opening and closing handle is turned up. Then open to the left. Squeeze the handle, open this side, put the magnetic ring in, and then open and close the handle to reset, the copper wire bends a small groove, the groove is facing the outer line, press the start. Then cut it at the required position, pay special attention at this time, The thread passes from the right side of the steel ring from the right to the left, and then wraps around on the wheel. In this case, when he waits for the round, the power will be less. Then press start.

         The winding of a loop coil is completed. There are three important points in the winding process. Let me emphasize first. First, the tension of the belt mentioned above is very important. If the thread is thin, the tension of our belt will break if it is too large. If the tension is too small, it won't be so smooth, it won't be so tight. Before the adjustment of the belt, the previous video said, loosen this knob, and then adjust the idler with another knob. The more the idler is toward the front, the greater the belt tension. Then the second is: the left and right position of the magnetic ring relative to the steel ring. When you see the enameled wire passing by, when you pass it, you need to align the center of the magnetic ring with the right side of the steel ring. ? It is adjusted by the adjustment handle on the clamping base, this is the second one. There is also the last one. In order to arrange the enameled wire relatively flat, the distance between the front and back of the magnetic ring should be as close as possible to the baffle of the ring coil winding machine. Where is his adjustment? It is also in the clamping seat. The front and rear handles are for adjustment.

Related Post

Toroidal coil winding machine

Toroidal coil winding machine

Toroidal coil winding machine

There are side-slip toroidal coil winding machines with processing coils, and belt-type toroidal coil winding machines with small-sized inductors.

Toroidal coil winding machines have the same specifications.Generally speaking, the smaller the inner diameter, the more difficult to process, and the thicker the wire diameter, the more difficult to process.

The video above shows the winding of an enameled wire with a diameter of 14mm and a diameter of 1.3mm.


Operation instruction of gear ring machine

Operation instruction of gear ring machine

Operation instruction of gear ring machine

Side-slip toroidal coil winding machine-wire passing method

Side-slip toroidal coil winding machine-wire passing method

Wire passing method of side-slip loop coil winding machine:

         For the side-slip toroidal coil winding machine, the setting method of the controller is basically the same as the belt-type toroidal coil winding machine, the difference is that the winding direction and the storage direction, when a person stands on the right side of the winding machine, The storage direction of the belt loop coil winding machine is counterclockwise, while the storage direction of the side slip loop coil winding machine is clockwise, and when winding, the belt loop coil winding machine and the belt loop The direction of the coil winding machine is the same, which is counterclockwise.

      Generally, in order to facilitate the observation of the winding situation, we can press the "Start" button twice in the winding phase. At this time, when we turn the rotating handle on the left side of the ring coil winding machine stand by hand, we can easily and clearly Observe the winding process of the enameled wire.